Series: Movie Tie-Ins
Alternate Mode: Buffalo Mine Protected Clearance Vehicle
Height: 7.5cm Length: 14.5cm Width: 5.5cm
A beige armoured truck with six grey tyres and two false spare tyres on the sides (painted the same colour), Bonecrusher has metallic blue painted windows and a huge arm extending from the front up over the roof, carrying a giant comb. As odd as that last bit sounds, the MPCV is an actual vehicle - Bonecrusher is licensed! The colours are fairly accurate, although the beige is a little duller than what seems to be normal (from the photos I've seen - it's not like these things are common around the street). The comb and segments of the arm are a slightly darker greenish brown shade of plastic, while orange warning lights below the side mirrors round out a simple yet logical and accurate colour scheme. There's a very subtle gold Decepticon logo stamped on the arm.
I have to give credit to whoever thought this toy up. We've had hundreds of sports cars & jet planes - it's not very often we see a Transformer with a vehicle mode that's _new_ to the line (where's my bus, dammit?!). Granted we've seen armoured trucks a few times, but never a dedicated mine clearing truck like this. The basic idea of this truck is that it's heavily armoured, rugged, and built to both withstand and clear mines. Which is where the giant arm comes in - the comb is the unsubtle clearance device. The sculpt on Bonecrusher is pretty good, too - the detailing is quite accurate (which makes sense, being licensed and all). The comb has eight teeth, one less than the actual MPCV, since it needs to split during transformation.
All six wheels roll, although the middle pair generally won't touch the table. While two wheels sit above the table slightly, Bonecrusher rolls well enough, which is the most important aspect for me. The arm, which attaches to the right side of his grille, is quite poseable. There's a rotator at the base, two hinges near the base (one back and forth, the other side to side) and a major hinge just above roof level (so that it can stow above the roof). The end result is a comb that can extend 15cm in front of the truck itself. Unlike the actual MPCV, the comb doesn't have any joints near its attachment point. However the comb splits into two - forming an attack claw (not an MPVC trait), and this claw can open and shut, with two joints per side. The joints closest to the claws themselves fold in independently while those further back work in unison, and are linked to a slider. Sliding back closes the claw and forward opens the claw.
On the whole this is a great vehicle. The originality is nice, and while the MPCV itself looks bizarre, the brute force portrayed here is fitting. I would have liked to see a little more poseability on the arm - one rotator just above the base of the arm would give it side to side motion, something it notably lacks. Even so, there's still play value in both the comb and the claw that it becomes. I would love to see this same concept carried onto a larger price scale, since the MPCV is a fairly massive truck, and of course that extra joint would be nice. All told, I love this vehicle mode, despite the limitation on his arm.
TRANSFORMATION TO ROBOT MODE
Fold the arm in slightly, so that it sits in the middle of his grille, swing the front wheels out and forward. Detach the rear wheels from the fenders, open out the sides of the truck, swing up the rear wheels. The sides are now arms and the wheel assemblies legs. Rotate the boots, push the spare tyres together and clip the groinplate over them, locking his legs in place. Swing his head into place. Open the claws on the front of his legs, swing out the claws on either side. Pivot the rear wheels down underneath his legs. Lift up two small panels on his shoulders, swing up the back sections of the truck (on the end of his arms), fold back the truck sides to reveal the hands, swing out his claw hands and bend the elbows. Fold the claw up on his back so that the two halves sit behind the front wheels.
Height: 14cm Width: 16.5cm
Bonecrusher's legs, head, groin and forearms are mainly green-brown whilst his slender chest, upper arms and backpack are beige. There are some orange painted details, a crest, shoulder panels and on the groin. His eyes, sunken into the face, are transparent red plastic. Unusually, there's no lightpipe here. The claws on the front and outsides of his feet are beige. The colour scheme is again fairly drab, but with more contrast which is welcome - the contrast gives this mode a different feel to the truck mode.
The shape here is markedly different to the truck mode. Granted there's quite a bit of shellforming here (a lot hangs off his arms), but the change is still notable. The body itself is thin and short, with much of the bulk in his limbs. While the truck was an angular block with flat surfaces, Bonecrusher's robot mode is full of organic curves with points on long limbs. I like this contrast - Bonecrusher's two different modes really convey the idea of an alien being hiding as a Earthen vehicle. The feet are claws, the arms long, rangy things ending in alien claws. The head is bizarre, looking vaguely insect like but mainly other-worldly. The upper arms stick out to the sides, the elbows bend downwards, and the forearms are quite long. His proportions are very much alien, which is in keeping with the theme of this toy. Whilst badly proportioned Transformer robot modes can be a burden, Bonecrusher's proportions _fit_ into what the designer was trying to achieve, and hence works in his favour.
The poseability is great. His head is on a ball joint, the shoulders swing and the elbows lift out to the sides - giving his forearms full range of movement. The claws extend thanks to a series of hinges - the extended forearms are 8cm long on their own. Bonecrusher's no doubt great at Greco-Roman wrestling. The hips are ball joints, the knees bend and there are rotators above his knees. The four claws on his feet work surprisingly well at stabilising poses, while the wheel in between also lends a hand. The heels fit nicely into the skating ability Bonecrusher displays in the movie, although the toy can't actually skate.
Oh, and then there's the claw which can deploy overhead, helping Bonecrusher's wrestling ability. Not a Decepticon you'd want to engage in hand to hand combat. It's worth noting that he lacks any sort of ranged weapon, mind you. The claws have quite a reach, but from afar he has no way of attacking.
A very unusual but thematically strong robot mode with great poseability, some unusual design elements, a good sculpt and a marked contrast to the vehicle mode. If there's a shortcoming here, it's the lack of an actual weapon - but with the long claws and the extra claw on his back, I don't really mind. I will concede that the unusual concept wont fit everyone's tastes, but it _is_ well executed, and for that reason I like the robot mode.
None that I'm aware of. Jungle Bonecrusher is a repaint of Bonecrusher.
Two vastly different modes that are only unified by the Claw Of Doom, but both modes are great in their own way. The vehicle mode brings something new to the Transformers toyline while the mine clearing comb is fun and its claw function is great. The Earthen military vehicle mode couldn't contrast more with the distinctly alien robot mode - and this fits into the movie's focus on the Transformers as aliens on our world. The play value is better than most movie deluxes, and the robot mode really is a lot of fun. Assuming you can get into the unusual themes, I'd definitely recommend this toy - 9.5/10